Automotive service equipment
Seal set (5pcs) for PL-4.0-2B. Spare part
2B-401 (40 x 52 x 5 mm) 2B-403 (40 x 9.5 x 2.5 mm) 2B-406 (63 x 5.7 mm) 2B-408 (63 x 8 x 2 mm) 2B-409 (63 x 53 x 8 mm)
Seal set (5pcs) for PL-4.0-2D. Spare part
E10/F10 - ⌀38 x 46 x 6.5 mm E11/F11 - ⌀38 x 6 x 2 mm E17/F17 - ⌀63 x 5.7 mm E18/F18 - ⌀63 x 10 x 2.5 mm E19/F19 - ⌀63 x 53 x 6 mm
Semi circle block for PL-4.0-2D. Spare part
Semi-circle block – spare part for the PULI PL-4.0-2D car lift. Used to replace a worn or damaged part and restore correct operation of the lift. Please check that your lift model matches before fitting.Brand: PULICompatibility: PL-4.0-2D liftType: spare part
Set of cones 4pcs.
Fits to 36 mm wheel balancer shafts Diameter range of cones: 1pcs. Max 135 mm, Min 90 mm 1pcs. Max 95 mm, Min 65 mm 1pcs. Max 80 mm, Min 50 mm 1pcs. Max. 65 mm, Min 40 mm
Shock absorber counter holding tool
For the removal and installation of the front and rear shock absorbers For the retention of the damper piston rod when repair work at the strut. (shock absorber, strut mounting, coil spring) Suitable for VW-Audi, Ford, Opel/Vauxhall, Japanese cars, etc. Wrench in two different sizes: 5 x 8 mm, 6 x 9 mm
Shock absorber removal tool / strut spreader
Expansion Force: 60N Spreading Range: 5.0 - 10 mm, Drive 16 mm HEX Suspension strut spreader tool can quickly help you remove the spring strut from the wheel bearing housing Strut spreader tool work on most of the car equipped with a pinch bolt style hub Compatible with VW, Audi, Ford, BMW, Peugeot, Renault, Seat, Skoda, Japanese vehicles
Shock absorber remover and installer kit 18pcs
Permits the removal of the top suspension nut by holding the strut piston, so it doesn’t rotate while turning the nut The go-through design of the socket and ratchet allows the extension to pass through the middle To be used in conjunction with a 1/2" Drive ratchet 1 pcs Go-Through Ratchet: 21 mm 7 pcs Go-Through 82mm Deep Sockets: 16, 17, 18, 19, 21, 22, 24mm 10 pcs Extensions: F Hex; 7, 8, 9 mm, M Hex; 6, 7, 8 mm, Slotted: 5 x 8, 6 x 8, 7.1 x 9.6 mm, T50
Shop stool with swivel seat
Capacity 113 kg (250 LBS) Overall dim. 515 x 515 x 730 mm Seat swivels 360 degrees Weight 5.76 kg Package size 680 x 510 x 90 mm
Slider for PL-4.0-2B / 2D. Spare part
Slider for PULI PL-4.0-2B and PL-4.0-2D vehicle lifts. This spare part replaces a worn or damaged slider to keep the lift working properly. Please check that your lift model matches before ordering.Brand: PULICompatibility: PL-4.0-2B / PL-4.0-2DType: spare part
Sliding hammer - mini type with 10pcs glue pads
Sliding hammer 0.43 kg 10 pcs. glue pads
Sliding hammer/puller CV joint removal set 4pcs
Use this easy-to-use CV joint puller, without spending a lot of effort, and without causing any damage to expensive aluminum transmission cases or other components With 63mm 48mm Joint Fork: Our kit includes opening 63mm and 48mm cv joint fork removing adapter, the CV Joint Fork is threaded internally, and the Slide Hammer stick is threaded externally. the joint fork could fit on the slide hammer stick, 63mm and 48mm fit most vehicle models, have a wide use This kit has everthing you need to remove CV axle or half shaft.
Sliding hammer/puller set 9pcs
2.5 kg Slide hammer with 570 mm shaft Twin leg puller: Internal capacity Ø 35 - 110 mm, reach 82 mm External capacity Ø 50 - 140 mm, reach 75 mm Triple leg puller: Internal capacity Ø 50 - 135 mm, reach 82 mm External capacity Ø 20 - 135 mm, reach 75 mm
Sliding hammer/puller set 9pcs.
2.5 kg Slide hammer with 570 mm shaft Twin leg puller: Internal capacity Ø 35 - 110 mm, reach 82 mm External capacity Ø 50 - 140 mm, reach 75 mm Triple leg puller: Internal capacity Ø 50 - 135 mm, reach 82 mm External capacity Ø 20 - 135 mm, reach 75 mm
Slotted special socket set 7pcs (10-19mm)
Used with specialized socket wrenches to unscrew fuel lines, temperature sensors, thermal switches, lambda probes and other elements with cables Range: 10, 11, 12, 13, 14, 17, 19 mm Drive: 3/8 "(10 mm) and 1/2" (12.5 mm) Sockets made of durable chrome vanadium steel Placed on a metal bar Type of cap: open
Spare part. Lifting arm rubber pad for PL-4.0-2D (rectangle)
Rectangle shape Dimensions 125 x 75 x 10 mm
Spark plug socket 14mm 3/8" Dr. (thin wall)
Thin walled Spark Plug socket with a spring clip to hold the plug Used on most Citroen vehicles Fitted with 14 mm Bosch spark plugs such as BMW E90335I N54 engine 2006, BMW Mini, Mercedes M156 engine, Peugeot 207 and 307, Renault 1.2 16v
Special socket for TESLA battery cover
Battery cover screw tool compatible with Tesla screw removal sleeve special battery box 5 angle tooth special wrench Easily remove the screws on the battery compartment cover Compatible with Tesla Model 3 model Y and other cars Material: CR-MO
Spoke wrench set 11pcs
Suitable for adjusting spoke tension and correcting buckled wheels Used on most OEM or aftermarket wheel spokes compatible with Honda, Kawasaki, Suzuki, Yamaha, KTM, Husky and others motorcycles Tips are made from hardened steel with a chrome finish for strength Sizes 5.0, 5.2, 5.4, 5.6, 5.8, 6.0, 6.2, 6.4, 6.6, 6.8, 7.0 mm
Spot welding machine and dent bar set
Specifications Suppport voltage: 220V / ~50 hz Input power: 3 KW Input current: 32 A (MAX.) Working mode: 7 Modes Normal working hours: Automatic mode program setting Vacuum suction: 180 KGS / 396.8 LBS Welding thickness of single side: 0.6~1.2mm The item has 7 modes for your choice. With the simple operation panel. it won't be a trouble to use the machine. The switch among those modes can be very steady and smooth. The Spot Dent Puller Dent Puller only produces small solder spots, which mean it won't damage the anticorrosive paint on the other side of the panel. The cooling system can quickly achieve heat dissipation, and make the machine not so easy to burn. Providing high efficiency during your work and fast heat dissipation is ensured. Suitable for Sheet metal fire, meson, straight pull, spot welding, flattening, wave line, stud, OT film, triangular and so on. Package Includes 1pcs x Car Body Stud Welder Dent Repair Main Unit 1pcs x Spanner 1pcs x Hook Hammer 1pcs x Manual Sucker 1pcs x Triangle Chuck 1pcs x Wave Line Kit 2pcs x Carbon Rods 1pcs x Manual (English) 1pcs x Carbon Rod Connector 2pcs x Packs of Gasket Kit (Long and Round) 10pcs x Triangle Straight Pull Gaskets Notice: This spot welding machine has an automatic overheating protection function. When the machine is overused, the machine may stop working for a few minutes. During this time, the indicator light in the middle of the screen will stay on. Before welding, please protect your eyes and wear protective clothing. Do not wear metal jewelry on your hands. Please make sure that the product is connected to the ground wire and the grounding power cord is intact. Due to the heavy weight of the product, unnecessary squeezing is unavoidable during transportation. If you cannot turn it on, please check the switch or fuse in time.
Spot welding machine for aluminum and dent bar set
Specifications Suppport voltage: 220V / ~50 hz Input power: 3 KW Input current: 60-90 A (AC1V-7V) Working mode: 2 modes (smart automatic and manual) Autonomous mode setting Max pulling force: 2 tons Single side welding thickness: 0.6-1.2 mm Small-scale Spot Welding: This spot welder makes a small welding spot that means it won't damage the anti-corrosive paint on the other side of the panel. Fast Heat Radiation: The side holes can help the dent puller quickly dissipate heat.The heating of the machine has the function of overheating protection. When the temperature reaches a critical value, the welding machine will automatically stop working, and can continue to operate after cooling. the automatic overheating protection function can ensure the spot welder dent puller work continuously for a long time without worrying about burnout. It features high efficiency, practicality, and reliability. High precision PCB control circuit board: Microcomputer control, imported components, multi-layer chip technology, dust prevention, moisture-proof, and anti leakage treatment. By presetting expert welding mode parameters, novices can also become masters of gold. The computer automatically memorizes the last operation for the convenience of next boo Intelligent induction repair technology: Intelligent induction/manual integrated one button switch Quick heating repair technology: The combination of quick drawing tools and hot spray guns can achieve one-time drawing repair of concave parts of aluminum body Double grounding design: Fully the current direction of aluminum mesons during the welding process, prevents arc welding, and makes the welding more secure High energy capacitor: Capable of withstanding greater charging and discharging currents than 1 million times, with faster speed Automatic adjustment of welding gun: Different studs require different welding forces, so the welding gun pressure can be automatically adjusted according to different studs Core patented technology: Plug and play pull ring: Plug and play pull ring: regardless of M4, M5, M6 screws, plug and play, greatly improving work efficiency. Avoiding damage and disposal of the pull ring caused by stuck or broken nails. Fast charging and discharging technology: The super large energy storage capacitor has a large capacity, fast charging and discharging speed, and long service life, ensuring the welding firmness of the machine. The power storage process only requires 0.3S, which is called fast charging technology. Rapid heating repair technology: (patented technology) Aluminum body has poor tensile resistance and cannot achieve spot welding and direct pulling like iron body. The combination of a quick puller and a hot spray gun can achieve rapid drawing and repair of dents in aluminum body parts. Package Includes 1pcs x Spot welding machine for aluminum 1pcs x Dent pull lever bar 1pcs x Pull hook/comb (6 hooks) 1pcs x Ruller 500 mm 1pcs x Hammer 1pcs x Scriber 2pcs x Sanding pads 3pcs x Stud coller 3pcs x Studs M3 / M4 / M5 (1 bag each) 9pcs x OT Pull Gaskets Aluminum Notice: Due to the fact that the aluminum body is made of 1.2mm aluminum material, inaccurate welding power operation can cause poor welding or penetration. When selecting a model, please try to choose a new generation of digital high-precision control models. Aluminum body has high strength and poor local tensile performance, making it prone to cracking. In order to improve its strength during the body manufacturing process, the elongation rate has exceeded 30%. Therefore, special tools must be used when repairing. During the repair process of aluminum body, one of the time-consuming tasks after welding the threaded nails is to screw in and out the threaded nails with the pull ring, which is time-consuming and labor-intensive. And the broken threaded nails in the later stage also delay the reuse of the pull ring. The aluminum body is made of aluminum magnesium alloy, with a melting point of 630-650C. The stress relieving annealing temperature of aluminum magnesium alloy is between 320 and 360 ° C, which can be used for deformation repair. During the repair process, tools that do not exceed this temperature must be used to assist heating. There are also areas with reinforced adhesive connections on the back, and the heating temperature should not be too high. The firmness of meson welding will directly affect the repair effect. The double grounding point design fully ensures the current direction, avoids arc deviation, makes welding more secure, and thus ensures repair quality. Package dimensions 505 x 320 x 350 - 17 kg
Spring for protection hood of PL-1150
100-112 (P-100-330000-0) Overall length 87 mm Diameter 25 mm
Stainless steel scraper set 4pcs
Set of rectangular spatulas. Made of stainless, resilient sheet metal finished with a plastic handle. The set includes spatulas of the following widths: 50 mm 80 mm 100 mm 120 mm Used for precise application of compounds and leveling of surfaces prior to varnishing.
Standard weight 100g for Wheel balancers. Spare part
Standard (calibration) weight for wheel balancers. Used to calibrate the balancer and check its accuracy so that measurement results are reliable. Best kept next to the machine so it is always at hand.Brand: PULIMass: 100 gType: spare part